Dimension card

One sheet per standard, sized for A4 and meant for a workshop wall. Each card carries the size range, what the nominal size is measured on, and the groove dimensions the standard fixes — so the part can be identified without a catalogue or a phone.

Print the whole set or a single sheet. Each card names what its figures rest on: two independent published specifications where we have them, and a single named manufacturer where we do not. Where we have neither, the card says so rather than filling the gap.

DIN 471

External circlips

Axial Supplyaxialsupply.co.uk

The nominal size is the shaft the ring fits — never a dimension of the ring itself. Measure the shaft beside the groove, not the ring you removed: a used ring has been flexed and reads wrong.

Nominal	Groove Ø	Groove width	Thickness	Edge margin
3 •	2.8	0.5	0.4	0.3
4 •	3.8	0.5	0.4	0.3
5 •	4.8	0.7	0.6	0.3
6 •	5.7	0.8	0.7	0.5
7 •	6.7	0.9	0.8	0.5
8 •	7.6	0.9	0.8	0.6
9 •	8.6	1.1	1	0.6
10 •	9.6	1.1	1	0.6
11 •	10.5	1.1	1	0.8
12 •	11.5	1.1	1	0.8
13 •	12.4	1.1	1	0.9
14 •	13.4	1.1	1	0.9
15 •	14.3	1.1	1	1.1
16 •	15.2	1.1	1	1.2
17 •	16.2	1.1	1	1.2
18 •	17	1.3	1.2	1.5
19 •	18	1.3	1.2	1.5
20 •	19	1.3	1.2	1.5
21 •	20	1.3	1.2	1.5
22 •	21	1.3	1.2	1.5
24 •	22.9	1.3	1.2	1.7
25 •	23.9	1.3	1.2	1.7
26 •	24.9	1.3	1.2	1.7
28	26.6	1.6	1.5	2.1
29	27.6	1.6	1.5	2.1
30	28.6	1.6	1.5	2.1

All dimensions in millimetres. • marks a size Axial Supply stocks. Edge margin is the minimum from groove to the end of the shaft or bore. Tolerances are in the standard and are not reproduced here. Cross-checked against two independent published specifications.

DIN 472

Internal circlips

Axial Supplyaxialsupply.co.uk

The nominal size is the bore the ring fits — never a dimension of the ring itself. Measure the bore beside the groove, not the ring you removed: a used ring has been flexed and reads wrong.

Nominal	Groove Ø	Groove width	Thickness	Edge margin
8 •	8.4	0.9	0.8	0.6
9 •	9.4	0.9	0.8	0.6
10 •	10.4	1.1	1	0.6
11 •	11.4	1.1	1	0.6
12 •	12.5	1.1	1	0.8
13 •	13.6	1.1	1	0.9
14 •	14.6	1.1	1	0.9
15 •	15.7	1.1	1	1.1
16 •	16.8	1.1	1	1.2
17 •	17.8	1.1	1	1.2
18 •	19	1.1	1	1.5
19 •	20	1.1	1	1.5
20 •	21	1.1	1	1.5
21 •	22	1.1	1	1.5
22 •	23	1.1	1	1.5
24 •	25.2	1.3	1.2	1.8
25 •	26.2	1.3	1.2	1.8
26 •	27.2	1.3	1.2	1.8
28 •	29.4	1.3	1.2	2.1
30 •	31.4	1.3	1.2	2.1
31 •	32.7	1.3	1.2	2.6
32	33.7	1.3	1.2	2.6

All dimensions in millimetres. • marks a size Axial Supply stocks. Edge margin is the minimum from groove to the end of the shaft or bore. Tolerances are in the standard and are not reproduced here. Cross-checked against two independent published specifications.

DIN 6799

E-clips

Axial Supplyaxialsupply.co.uk

The nominal size is the shaft groove the ring fits — never a dimension of the ring itself. Measure the shaft groove beside the groove, not the ring you removed: a used ring has been flexed and reads wrong.

Nominal	Groove Ø	Groove width	Thickness	Edge margin
1.5 •	1.5	0.44	0.4	0.8
1.9 •	1.9	0.54	0.5	1
2.3 •	2.3	0.64	0.6	1
3.2 •	3.2	0.64	0.6	1
4 •	4	0.74	0.7	1.2
5 •	5	0.74	0.7	1.2
6 •	6	0.74	0.7	1.2
7 •	7	0.94	0.9	1.5
8 •	8	1.05	1	1.8
9 •	9	1.15	1.1	2
10 •	10	1.25	1.2	2

All dimensions in millimetres. • marks a size Axial Supply stocks. Edge margin is the minimum from groove to the end of the shaft or bore. Tolerances are in the standard and are not reproduced here. Source: Springmasters Ltd — one manufacturer specification, not two independent references.

Sources

Every dimension on these cards was taken from a published manufacturer specification. The DIN 471 and DIN 472 figures were checked against a second, independent one; the DIN 6799 figures rest on a single manufacturer's data and are attributed to them on the card itself.